About Our Courses
Our Courses
Industrial Training Sheet for Engineering Student
কোর্স গুলি যে সকল ডিপার্টমেন্টের শিক্ষার্থীদের জন্য প্রযোজ্যঃ ১.ইলেকট্রিক্যাল ২.ইলেকট্রনিক্স ৩.ইলেকট্রিক্যাল এবং ইলেকট্রনিক্স ৪.ইলেকট্রোমেডিক্যাল ৫.আইপিসিটি ৬.মেকানিক্যাল ৭.পাওয়ার ৮.ইলেকট্রিক্যাল অ্যান্ড টেলিকমিউনিকেশন
Applicable: For 1. Electrical 2.Electronics 3.Electrical & Electronics 4.Electromedical 5.IPCT 6. Mechanical 7. Power 8. Electrical and TelecommunicationA. Industrial Automation and PLC
Course Fee: TK. 10000(for a single student )
TK.8000 for group above 10 (Student)
TK.12000 (for service holder )
Required Documents for Admission:
1. Passport size photograph (1 copy)
2. Photocopy of Admit Card/Office ID/NID (1 copy)
1.Commercial name of wiring materials and selection.
2.House wiring practical practice.
3.Total load calculation procedure of a Building.4.House wiring cable specification
6.Specification, selection, connection diagram for Magnetic contactor.
7.Motor control Circuit practical practice by using
Magnetic Contactor.
8.Specification, Ampere selection, the connection of Safety Thermal Overload Relay for the motor.
9.Safety motor protection control circuit practical practice by using thermal Overload Relay.
10.specification, selection, connection procedure of 3 phase induction Motor.
10.specification, selection, connection procedure of 3 phase induction Motor.
11.Motor checking procedure from Multimeter and Star Delta connection physical practice.
12.specification, selection, connection diagram for Magnetic Relay.
13.Motor control circuit practice by using Relay.
14.3 Phase failure motor protection circuit practice by using Relay.
15.Specification, selection, connection diagram for On delay timer.
16.Motor control circuit practice by using the “ON Delay” timer.
17.Function and connection procedure of “OFF Delay” Timer.
18.Connection and setting procedure of twin Timer/Sequential Timer.
19.Traffic signal control practice by using sequential Timer.
20. Auto water level control circuit practice for multistoried Building/Industry.
21.Manual Change over switch connection procedure for the duel power of a Multi stored Building.
22.Auto Transfer Switch (ATS) Fabricating Procedure and practical Practice.
23.Auto control of High rise Building duel Power supply procedure by using ATS with delay on timer to protect hunting from REB.
24.Bus Bar copper calculation procedure and practical practice as per variation of Load.
25. Motor forward and reverse controlling circuit practice by using a Magnetic Contactor.
26.Safety panel switching control by using the limit sensor of the power plant.
27.Star Delta 3 phase easy connection procedure from Motor.
28. Star delta control circuit connection practice by using Timer.
29.Electrical Troubleshooting practice from the industrial Panel Board.
30. Modern proximity(2Wire) sensor signaling metal Detector circuit practice.
31.Photo Sensor(5 Wire) circuit practice for lift/Elevator.
32.Name and selection of measuring instruments.
33.Measuring procedure from the multi meters.
34. Measuring procedure from Clamp-on meter.
35.Measuring procedure from Megger Tester.
36.Connection procedure for Digital and analog meters.
37.PLC(Programming Logic Controller) Basic, Theory, and Selection procedure.
38.Software Installation and Ladder Diagram Practice with the computer.
39.Ladder diagram converting, Editing, and Transferring from computer to PLC.
40.Ladder diagram transferring from PLC to Load.
41. Hardware connection procedure between PLC and Load.
42.PLC On-Line Monitoring and troubleshooting Procedure.
43. Industrial DOL(Direct On-Line) switch connection procedure.
44.Industrial MMS(Manual Motor Starter) switch or MPCB using a
the procedure with the motor.
45.Industrial Cable selection and checking procedure.
45.Industrial Cable selection and checking procedure.
46.The benefit of using power factor for Industry.
47.Economy Power Factor Improvement capacitor selection
Procedure.
48.P.F.I (Power Factor Plant) Control Relay selection, controlling,
48.P.F.I (Power Factor Plant) Control Relay selection, controlling,
and connection practice.
49. Familiarization with Industrial Diode, LED, Zener
Diode, Checking, and practical practice.
50. Familiarization with Industrial Bridge Rectifier, checking
50. Familiarization with Industrial Bridge Rectifier, checking
Procedure, and practical practice.
B.Advance PLC, VFC Programming, Sub Station, and Automation:
Course Fee: TK. 6000(for student )
TK.5000 for Group above 10(Students)
TK.8000 (for service holder )
51.Busbar trunking system for Garments and Industry.
52.Familiarization and maintenance procedure of 3 phase Transformer.
53. Familiarization with SSR(Solid-state Relay), Checking procedure, and practice.
54.Digital Temperature controller type, connection practice.
55. Auto Temperature control circuit practice by using industrial Heater.
56. Industrial Substation Single Line Diagram Layout practice.
57. Familiarization with a voltage regulated IC and their checking and connection procedure.
58.Variable Frequency Drive/Frequency Inverter Advantage, operation, and connection with motor Procedure.
59.Inverter parameter selection procedure.
60.Inverter Internal and External switching and programming procedure and practice.
61.VFD Alarm Management and Maintenance procedure.
62.Autorun between VFD and PLC Programming from PLC.
63.Advance HMI (Human Machine Interface) Familiarization and programming practice.
64.Mitsubishi PLC Programming practice.
65.LS PLC Programming Practice.
66.Familiarization with HMI (Human Machine Interface).
67.Siemens logo comfort PLC Programming Practice.
68.Siemens S7-200 PLC Programming Practice.
69.Checking and Maintenance procedure of Magnetic Contactor.
70.Checking and maintenance procedure of Magnetic Relay.
C. Special Maintenance Course for Engineers
71.Familiarization with ISO Certification.
72.Familiarization with GMP(Good Manufacturing Practice).
73.Safety operation procedure (SOP).
74.Schedule maintenance procedure.
75.Preventive Maintenance Procedure.
76.History Card Managing Procedure.
77.BIN Card Managing Procedure.
78.Engineering spare parts collection, consumption, and ordering procedure.
79.Familiarization with fire fighting system, remedy, and equipment of the industry.
80.Familiarization with ETP(Effluent Treatment Plant) for Industry.
81.Familiarization with Solar Panel and connection Procedure with Load.
D. Mechanical Department
Mechanical Department Course Schedule
Part A: PLC and Electro-Mechanical Automation for Industry
Course Fee:
TK. 5000(for student )
TK.4000 for group above 10 (student)
TK.6000 (for service holder )
1. Name of House wiring Materials.2. House wiring Practical Practice.
3. Fire Alarm Installation of Garments Industries.
4. Specification, Selection, and Connection Diagram for Magnetic Contactor.
5. Motor control circuit practice by using a magnetic contactor.
6. Specification, ampere selection and connection of Thermal
Overload Relay for motor
7. Specification, ampere selection and connection of Magnetic Relay
8. Motor control circuit practice by using Relay.
9. Specification, ampere selection, and connection of "ON Delay
7. Specification, ampere selection and connection of Magnetic Relay
8. Motor control circuit practice by using Relay.
9. Specification, ampere selection, and connection of "ON Delay
Timer".
10. Motor control circuit practice by "ON Delay Timer".
11. Modern proximity sensor 2 wire connection, checking, and circuit practice.
12. Photosensor 5 wire connection and practical practice.
13. PLC Programming logic controller, basic theory, and selection procedure.
14. Software installation and Ladder Diagram practice with Computer.
15. Ladder diagram practice 01 circuit.
16. Ladder diagram practice 02 circuit.
17. Ladder diagram converting, Editing, and Transferring from computer to PLC Practice.
18. Programming practice from PLC to (Machine) Load.
19. Input and Output physical connection between PLC and Machine.
20. PLC online monitoring and troubleshooting practice.
PART B: Industrial Mechanical
22. Industrial Machinery Different type of Gear selection and Familiarization.
23. Industrial Gasket, O Ring, Mechanical Seal Selection, and Familiarization.
24. Industrial Belt Selection and Familiarization.
25. Workshop visit and Hands-on Practice.
26. Industry visit (Conditional).
ABC License (Training)
Course Fee 3000 Taka
1. House Wiring Materials Commercial Name2. Industrial Items Name, Specification Selection
3. Magnetic Contractor, Thermal Overload, Timer, Motor Specification, and Selection.
4. Sub-Station Single Line Diagram Practice.
5. 11KV to 33 KV Isolator, Metal Clad Switch, H.T Fuse, Kit-Kat Description.
6. Measuring Procedure by "Megger and Earth" Tester.
7. 11 KV/400V Transformer Checking Procedure.
8. Viva Related question Practice.
যে সকল ইন্ডাস্ট্রিয়াল সার্কিট বা প্রোজেক্ট আপনারা নিজ হতে তৈরি করবেন বা যেগুলো সম্পর্কে আমাদের কাছে শিখতে পারবেন,সেই প্রোজেক্ট গুলোর ভিডিও ব্যাক্ষা দেখার জন্যে ক্লিক করুন
The Industrial Circuits/Projects that you will develop all by yourself during your training period, to see the live video description of these projects kindly click here
আমাদের ট্রেনিং করানোর পদ্ধতি দেখার জন্যে দয়া করে ক্লিক করুন
To see how we provide training to our students kindly click here
ফ্রি ইন্ডাস্ট্রিয়াল অটোমেশন ক্লাস করার জন্য ক্লিক করুন
To Attend free Industrial Automation Class kindly Click here
কোন মন্তব্য নেই
We provide the best Industrial Training For Diploma as well as B.Sc Engineers in Bangladesh. If you have any queries about us, please let us know!!!